Here for Device Driver and System Development
Dial-Up Networking Errors
600 - An
operation is pending.
601 - The port handle is invalid.
602 - The port is already open.
603 - Caller's buffer is too small.
604 - Wrong information specified.
605 - Cannot set port information.
606 - The port is not connected.
607 - The event is invalid.
608 - The device does not exist.
609 - The device type does not exist.
610 - The buffer is invalid.
611 - The route is not available.
612 - The route is not allocated.
613 - Invalid compression specified.
614 - Out of buffers.
615 - The port was not found.
616 - An asynchronous request is pending.
617 - The port or device is already disconnecting.
618 - The port is not open.
619 - The port is disconnected.
620 - There are no endpoints.
621 - Cannot open the phone book file.
622 - Cannot load the phone book file.
623 - Cannot find the phone book entry.
624 - Cannot write the phone book file.
625 - Invalid information found in the phone book.
626 - Cannot load a string.
627 - Cannot find key.
628 - The port was disconnected.
629 - The port was disconnected by the remote machine.
630 - The port was disconnected due to hardware failure.
631 - The port was disconnected by the user.
632 - The structure size is incorrect.
633 - The port is already in use or is not configured for Remote Access
634 - Cannot register your computer on the remote network.
635 - Unknown error.
636 - The wrong device is attached to the port.
637 - The string could not be converted.
638 - The request has timed out.
639 - No asynchronous net available.
640 - A NetBIOS error has occurred.
641 - The server cannot allocate NetBIOS resources needed to support the
642 - One of your NetBIOS names is already registered on the remote network.
643 - A network adapter at the server failed.
644 - You will not receive network message popups.
645 - Internal authentication error.
646 - The account is not permitted to log on at this time of day.
647 - The account is disabled.
648 - The password has expired.
649 - The account does not have Remote Access permission.
650 - The Remote Access server is not responding.
651 - Your modem (or other connecting device) has reported an error.
652 - Unrecognized response from the device.
653 - A macro required by the device was not found in the device .INF
654 - A command or response in the device .INF file section refers to
an undefined macro
655 - The <message> macro was not found in the device .INF file
656 - The <defaultoff> macro in the device .INF file section contains
an undefined macro
657 - The device .INF file could not be opened.
658 - The device name in the device .INF or media .INI file is too long.
659 - The media .INI file refers to an unknown device name.
660 - The device .INF file contains no responses for the command.
661 - The device .INF file is missing a command.
662 - Attempted to set a macro not listed in device .INF file section.
663 - The media .INI file refers to an unknown device type.
664 - Cannot allocate memory.
665 - The port is not configured for Remote Access.
666 - Your modem (or other connecting device) is not functioning.
667 - Cannot read the media .INI file.
668 - The connection dropped.
669 - The usage parameter in the media .INI file is invalid.
670 - Cannot read the section name from the media .INI file.
671 - Cannot read the device type from the media .INI file.
672 - Cannot read the device name from the media .INI file.
673 - Cannot read the usage from the media .INI file.
674 - Cannot read the maximum connection BPS rate from the media .INI
675 - Cannot read the maximum carrier BPS rate from the media .INI file.
676 - The line is busy.
677 - A person answered instead of a modem.
678 - There is no answer.
679 - Cannot detect carrier.
680 - There is no dial tone.
681 - General error reported by device.
682 - ERROR WRITING SECTIONNAME
683 - ERROR WRITING DEVICETYPE
684 - ERROR WRITING DEVICENAME
685 - ERROR WRITING MAXCONNECTBPS
686 - ERROR WRITING MAXCARRIERBPS
687 - ERROR WRITING USAGE
688 - ERROR WRITING DEFAULTOFF
689 - ERROR READING DEFAULTOFF
690 - ERROR EMPTY INI FILE
691 - Access denied because username and/or password is invalid on the
692 - Hardware failure in port or attached device.
693 - ERROR NOT BINARY MACRO
694 - ERROR DCB NOT FOUND
695 - ERROR STATE MACHINES NOT STARTED
696 - ERROR STATE MACHINES ALREADY STARTED
697 - ERROR PARTIAL RESPONSE LOOPING
698 - A response keyname in the device .INF file is not in the expected
699 - The device response caused buffer overflow.
700 - The expanded command in the device .INF file is too long.
701 - The device moved to a BPS rate not supported by the COM driver.
702 - Device response received when none expected.
703 - ERROR INTERACTIVE MODE
704 - ERROR BAD CALLBACK NUMBER
705 - ERROR INVALID AUTH STATE
706 - ERROR WRITING INITBPS
707 - X.25 diagnostic indication.
708 - The account has expired.
709 - Error changing password on domain.
710 - Serial overrun errors were detected while communicating with your
711 - RasMan initialization failure. Check the event log.
712 - Biplex port is initializing. Wait a few seconds and redial.
713 - No active ISDN lines are available.
714 - Not enough ISDN channels are available to make the call.
715 - Too many errors occurred because of poor phone line quality.
716 - The Remote Access IP configuration is unusable.
717 - No IP addresses are available in the static pool of Remote Access
718 - PPP timeout.
719 - PPP terminated by remote machine.
720 - No PPP control protocols configured.
721 - Remote PPP peer is not responding.
722 - The PPP packet is invalid.
723 - The phone number, including prefix and suffix, is too long.
724 - The IPX protocol cannot dial-out on the port because the computer
is an IPX router.
725 The IPX protocol cannot dial-in on the port because the IPX router
is not installed.
726 - The IPX protocol cannot be used for dial-out on more than one port
at a time.
727 - Cannot access TCPCFG.DLL.
728 - Cannot find an IP adapter bound to Remote Access.
729 - SLIP cannot be used unless the IP protocol is installed.
730 - Computer registration is not complete.
731 - The protocol is not configured.
732 - The PPP negotiation is not converging.
733 - The PPP control protocol for this network protocol is not available
on the server.
734 - The PPP link control protocol terminated.
735 - The requested address was rejected by the server.
736 - The remote computer terminated the control protocol.
737 - Loopback detected.
738 - The server did not assign an address.
739 - The remote server cannot use the Windows NT encrypted password.
740 - The TAPI devices configured for Remote Access failed to initialize
or were not installed correctly.
741 - The local computer does not support encryption.
742 - The remote server does not support encryption.
743 - The remote server requires encryption.
744 - Cannot use the IPX net number assigned by the remote server. Check
the event log.
752 - A syntax error was encountered while processing a script.
If a reinstall
of dun and/or TCP/IP is required, see this Microsoft knowledge base article
for Win 95/98 instructions to remove and reinstall dun's and TCP/IP. Here
© 2001-2006 © Copyright Karl Davis.
part of this site may be reproduced in any format.All documents author
acknowledged are copyright retained by the author.
links or Errors ? Please email the Webmaster